Research and Publications

Research Grants

  • Flow Physics Modelling and Design Optimization of an Exhaust-air Energy Extractor in the Cooling Tower Applications (2019-2021); FRGS Research Grant 2018, Total Amount: RM 100,000.00; Funded by Ministry of Higher Education (MOHE), Govt. of Malaysia. Investigators: Dr. Sukanta Roy (PI), A/Prof. Law Ming Chiat; A/Prof. Perumal Kumar; Dr. Aja Ogboo Chikere; Dr. Yam Ke San.

  • Mathematical Formulation and Analysis of Boiling Heat and Mass Transfer Subject to Simultaneous Microwave Ultrasound Irradiation (2019-2021); FRGS Research Grant 2018, Total Amount: RM 92,800.00; Funded by Ministry of Higher Education (MOHE), Govt. of Malaysia. Investigators: A/Prof. Vincent Lee Chieng Chen (PI); A/Prof. Law Ming Chiat; Dr. You Kok Yeow.

  • Impact of Palm Oil Based Minimum Quantity of Lubrication on Machinability of Ti and its Alloy (Ti-6Al-4V) (2019-2021); FRGS Research Grant 2018, Total Amount: RM 70,000.00; Funded by Ministry of Higher Education (MOHE), Govt. of Malaysia. Investigators: Dr. Sumaiya Islam (PI), A/Prof. Vincent Lee Chieng Chen; A/Prof. Sujan Debnath; A/Prof. Moola Mohan Reddy; Dr Neamul Ahsan Noman Khandoker.

  • Finite Element Modelling and Verification Study of a Helideck Perimeter Net (2018-2019); Consultancy Research Project; Total Amount: RM 30,000.00; Funded by Torr Energy Sendirian Berhad; Investigators: Vincent Lee Chieng Chen.

  • MySaBRIX: App based Brix refractometer to measure brix index of fruits and vegetables in Sarawak (2018-2020). Sarawak Multimedia Authority grant 2018; Total Amount: RM 150,000.00; Funding by Sarawak Multimedia Authority; Investigators: Dr. Denni Kurniawan (PI), Dr. Fethma Binti M. Noor, Dr. Tony Hadibarata, Dr. Sung Aun Naa, Ir. Lim Chye Ing

  • A Blended Learning Approach to Teach Engineering Mechanics (2018-2019); Curtin Malaysia Teaching Innovation Project (CMTIP) 2018; Total Amount: RM 2,000.00; Investigators: Lai Zhenyue (PI); Vincent Lee Chieng Chen.

  • Convention Funding Support (2018-2022); Total Amount: RM 132,000.00; Funding by Sarawak Convention Bureau; Investigators: Dr. Fethma Binti M. Noor  

  • Move Towards Technology-driven Concept-based Learning (2017-2018); Curtin Sarawak Teaching Innovation Project (CSTIP) 2017; Total Amount: RM 2,000.00; Funding by Curtin Sarawak Teaching Innovation Project (CSTIP);  Investigators: Dr. Henry Elochukwu Okafor (PI), A/Prof. Raoof Gholami Mian Poshteh, Dr. Aja Ogboo Chikere.

  • Thermal and Total Performance Enhancement of Inclined Solar Chimney Power Plant Using Underneath Air-vent and thermal Storage medium (2016-2018); FRGS Research Grant 2016, Total Amount: RM 97,200.00; Funded by Ministry of Higher Education (MOHE), Govt. of Malaysia. Investigators: Dr. Aja Ogboo Chikere (PI), Prof. Hussain H. Jaafer Al Kayiem; A/Prof. Zainal Ambri b. Abdul Karim; A/Prof. Chinnasamy Palanichamy; Dr. Meheron Selowara Joo.

  • A Mathematical Model of a Circular Force Transducer with Uniform Stress Distribution (2016-2018); FRGS Research Grant 2016, Total Amount: RM 97,200.00; Funded by Ministry of Higher Education (MOHE), Govt. of Malaysia. Investigators: Dr. Neamul Ahsan Noman Khandoker (PI), A/Prof. Sujan Debnath; Dr. Muhamad Ekhlasur Rahman; A. Prof. Lau Hieng Ho; Dr. Sumaiya Islam. 

 

List of Publications:2019

  • M.B. Upama, M.A. Mahmud, H.Yi, N.K. Elumalai, G. Conibeer, D. Wang, C. Xu, A. Uddin, Low-temperature processed efficient and colorful semitransparent perovskite solar cells for building integration and tandem applications, Organic Electronics, 2019, [IF 3.4], doi: 10.1016/j.orgel.2018.11.037

  • L. Duan, N.K. Elumalai, Y. Zhang, A. Uddin, Progress in non-fullerene organic solar cells, Solar Energy Materials and Solar Cells, 2019, [IF 5.1], doi: 10.1016/j.solmat.2018.08.010

  • Law, M. C., J. S. L. Chang, Y. S. Chan, D. Y. Pui, and K. Y. You. 2019. “Experimental characterization and modeling of microwave heating of oil palm kernels, mesocarps, and empty fruit bunches.” Drying Technology 37 (1): 69-91.

  • Leong, V. H., H. Ben Mahmud, M. C. Law, C. Y. H. Foo, and I. S. Tan. 2019. “A numerical modelling and simulation of core-scale sandstone acidizing process: a study on the effect of temperature.” Journal of Petroleum Exploration and Production Technology 9 (1): 483-516.

  • Yeong, S. P., M. C. Law, K. Y. You, Y. S. Chan, and V. C. C. Lee. 2019. “A coupled electromagnetic-thermal-fluid-kinetic model for microwave-assisted production of Palm Fatty Acid Distillate biodiesel.” Applied Energy: 457-475.

  • Lee, G. L., M. C. Law, and V. C. C. Lee. 2019. “Modelling of liquid heating subject to simultaneous microwave and ultrasound irradiation.” Applied Thermal Engineering: 1126-1140.

  • San Yam, K., Bourdillon, A., Sawko, R. and Thompson, C., 2019. Modelling solidification of binary mixtures in cavity and channel flows. Computational Thermal Sciences: An International Journal, Volume 11(3).

 

List of Publications:2018

  • Al-Kayiem, Hussain H., Sreejaya K. V. and Ogboo Chikere Aja. 2018, “Experimental and Numerical Analysis of the Influence of Inlet Configuration on the Performance of a Roof Top Solar Chimney” Energy and Buildings, Vol. 159, pp 89-98 (Elsevier). doi:10.1016/j.enbuild.2017.10.063; Impact Factor: 4.067

  • S. Roy, R. Das, and U.K. Saha, 2018, An Inverse method for optimization of geometric parameters of a Savonious-style wind turbine. Energy Conversion and Management, Vol 155, pp. 116–127 (Elsevier). doi:10.1016/j.enconman.2017.10.088; Impact factor: 5.589

  • M.B. Upama, N.K. Elumalai, M.A. Mahmud, C. Xu, M. Wright, D. Wang, A. Uddin, Enhanced electron transport enables over 12% efficiency by interface engineering of non-fullerene organic solar cells, Solar Energy Materials and Solar Cells, 2018, [IF 5.1], DOI: 10.1016/j.solmat.2018.08.010
  • M.C. Law, J.S.L. Chang, Y.S. Chan, D.Y. Pui, K.Y. You, “Experimental characterization and modeling microwave heating of oil palm kernel, mesocarp and empty fruit bunches”, Drying Technology, doi: 10.1080/07373937.2018.1439057

  • Van Hong Leong, Hisham Ben Mahmud, Ming Chiat Law, Henry Chee Yew Foo, Inn Shi Tan, “A comparison and assessment of the modelling and simulation of the sandstone matrix acidizing process: A critical methodology study”, Journal of Natural Gas Science and Engineering, 57, pp 52-67, 2018. 

  • Mas Ayu, S. Izman, R. Daud, A. Shah, Mahmood Anwar, G. Krishnamurithy, T. Kamarul, “In-Vitro Biocompatibility Study of Hydroxyapatite Coated On Co-Cr-Mo with Oxide Interlayer”, Jurnal Teknologi, Vol 80 (1), 35-42, 2018 (Scopus).
  • Mesfin Gizaw Zewge, Aja Ogboo Chikere and Abdulwehab A. Ibrahim. 2018, “Numerical Modelling of Performance on Batch Blade Savonius Turbine Using ANSYS” In proceedings of ASET 2018 First Multi Conference on Advances in Science and Engineering Technology – Renewable and Sustainable Energy International Conference, Dubai 6th to 7th February 2018

  • Omid Nabinejad, D Sujan, Muhammad Ekhlasur Rahman, Willey Yun Hsien Liew, Ian J Davies (2018) “Hybrid Composite Using Natural Filler and Multi-Walled Carbon Nanotubes (MWCNTs)” Applied Composite Materials, Springer (ISI & SCOPUS indexed, IF 1.217)

  • Mohammad Asyraf, Mahmood Anwar, Scott Van Stratten, Sujan Debnath and Izman Sudin, “Temperature Effect on the Electrical Behaviour of Nanosilver Doped Conductive Polymer”, DuraBI 2018 (won the Best Paper Award), Sarawak, Malaysia.
  • Nabinejad & D. Sujan. (2018) “Mechanical Performance and Moisture Absorption of Unidirectional Bamboo Fiber Polyester Composite”, Materials Science Forum, Vol. 911, pp. 88-94, 2018

  • Mohammad Yeakub Ali, Md Abdul Maleque, Asfana Banu, Abdus Sabur, Sujan Debnath (2018) “Micro Electro Discharge Machining of Non-Conductive Ceramic”, Materials Science Forum, Vol. 911, pp. 20-27, 2018

 

List of Publications:2017

  • Nabinejad, D Sujan, ME Rahman, IJ Davies (2017) “Effect of filler load on the curing behaviour and mechanical and thermal performance of wood flour filled thermoset composites” Journal of Cleaner Production, Vol. 164, pp. 1145-1156  (IF 5.715)

  • Lee V.C.-C., Chai, C.H., Law, M.C., Wee, S.K., “On the analysis of impedance-driven reverse flow dynamics”, Journal of Engineering Science and Technology, 12(2), pp451,459, 2017

  • Jessie S.L. Chang, Y.S. Chan, M.C. Law, C.P. Leo, “Comparative microstructure study oil palm fruit bunch fibre, mesocarp and kernel after microwave pre-treatment”, International Conference on Materials Technology and Energy, Miri, Sarawak, Malaysia, 2017, IOP Conf. series: Material Science and Engineering

  • S.P. Yeong, M.C. Law, V.C.C. Lee, Y.S. Chan, “Modelling batch microwave heating of water”, International Conference on Materials Technology and Energy, Miri, Sarawak, Malaysia, 2017, IOP Conf. series: Material Science and Engineering.

  • Mohammad Asyraf, Mahmood Anwar, Law Ming Sheng, and Michael K. Danquah, “Recent Development of Nanomaterial-Doped Conductive Polymers”, JOM, The Journal of The Minerals, Metals & Materials Society (TMS), Springer, Vol 69 (12), 2515-2523,2017 (IF: 1.798).

  • Caleb Acquah, Michael K. Danquah, Charles K. S. Moy, Mahmood Anwar, and Clarence M. Ongkudon, “Thermogravimetric characterisation of ex situ polymethacrylate (EDMA-co-GMA) monoliths”, The Canadian Journal of Chemical Engineering, Wiley, Vol 95 (7), 1345-1351,2017 (IF: 1.356).

  • Caleb Acquah, Michael K. Danquah, Charles K. S. Moy, Mahmood Anwar, and Clarence M. Ongkudon, “Parametric investigation of polymethacrylate monolith synthesis and stability via thermogravimetric characterisation”, The Asia-Pacific Journal of Chemical Engineering, Wiley, Vol. 12: 352–364, 2017 (IF= 0.836).

  • Dalton Sunday Oseghale, Ahmad, F.M., and Aja Ogboo Chikere (2017) Status Evaluation of Palm Oil Waste Management Sustainability in Malaysia: OIDA International Journal of Sustainable Development, Ontario International Development Agency, ISSN 1923-6654 (print) ISSN 1923-6662 (online).

  • Wilson Phua Yuen Zheng and Aja Ogboo Chikere “Review of Solar Chimney Power Plant Simulation and Modelling Approaches” Paper accepted in the One Curtin International Postgraduate Conference (OCPC 2017)

  • Dalton Sunday Oseghale, Ahmad, F.M., and Aja Ogboo Chikere (2017) A Review on the Status of the Environmental Management System (EMS) For Palm Oil Industry in Malaysia, in the proceeding of Asian Conference on Sustainability, Energy & the Environment (ACSEE 2017)

  • Aja Ogboo Chikere, Meheron Selowara Joo, and Patrick Okwudiri Ukwuaku “Personality Test Effect on Team Selection and Students’ Performance” In proceedings of International Conference on Teaching and Learning, Language, Literature & Linguistics (ICT4L), Kuala Lumpur, Malaysia. 2017

  • Aja Ogboo Chikere, Meheron Selowara Joo, and Patrick Okwudiri Ukwuaku “Impact of Engineering Final Year Project Research Method on Student’s Development in Knowledge Construction” In proceedings of International Conference on Teaching and Learning, Language, Literature & Linguistics (ICT4L), Kuala Lumpur, Malaysia. 2017

  • Lee, V.C.C. and San Yam, K., 2017, August. Introduction of OpenStudio® for Work Integrated Learning: Case Study on Building Energy Modelling. In Asian Simulation Conference (pp. 349-358). Springer, Singapore.

  • Yam, K.S., Yem, W.L. and Lee, V.C.C., 2017. Evaluation of the Passive Cooling Strategies for Pei Min Sport Complex. In IOP Conference Series: Materials Science and Engineering (Vol. 217, No. 1, p. 012025). IOP Publishing.

  • Thet Tin Oo; Sujan Debnath (2017) “Application of carbon nanotubes in perovskite solar cells: A review” MANUFACTURING ENGINEERING CONFERENCE (MIMEC2017) , 2017, Vol.1902, p.020015 DOI: 10.1063/1.5010632 

  • Chien S.E.M., Reddy M.M., Lee V.C.C., and Sujan D. (2017) “The Study of Coated Carbide Ball End Milling Tools on Inconel 718 Using Numerical Simulation Analysis to Attain Cutting Force and Temperature Predictive Models at the Cutting Zone” Materials Science Forum, 882, pp. 28-35 

  • Omid, N., Sujan, D., Teh, J.Y., Willey, Y.H.L., Ian, J.D. (2017) “Influence of alkali treatment and nanoclay content on the properties of rice husk filled polyester composites” Materials Science Forum, 882, pp. 89-100. 

  • Sumaiya Islam, Noman Khandoker, Mohamad Izham, Tengku Azizi and Sujan Debnath (2017) “Development of a Low Cost MQL Setup for Turning Operations” MATEC Web of Conferences, Vol.95, p.10004 DOI: 10.1051/matecconf/20179510004

  • Chien S.E.M., Reddy M.M., Lee V.C.C., and Sujan D. (2017) “The Study of Coated Carbide Ball End Milling Tools on Inconel 718 Using Numerical Simulation Analysis to Attain Cutting Force and Temperature Predictive Models at the Cutting Zone” Materials Science Forum, 882, pp. 28-35 

  • Omid, N., Sujan, D., Teh, J.Y., Willey, Y.H.L., Ian, J.D. (2017) “Influence of alkali treatment and nanoclay content on the properties of rice husk filled polyester composites” Materials Science Forum, 882, pp. 89-100. 

  • Sumaiya Islam, Noman Khandoker, Mohamad Izham, Tengku Azizi and Sujan Debnath (2017) “Development of a Low Cost MQL Setup for Turning Operations” MATEC Web of Conferences, Vol.95, p.10004 DOI: 10.1051/matecconf/20179510004 

  • Bapi Sarkar, Moola Mohan Reddy and Sujan Debnath (2017) “Effect of machining parameters on surface finish of Inconel 718 in end milling” MATEC web of conferences., 2017, Vol.95, p.02009 DOI: 10.1051/matecconf/20179502009 

  • Yik Wan Pok, Sujan Debnath, Muhammad Ekhlasur Rahman, and Sharul Sham Dol (2017) “Effect of Bond Layer Properties to Thermo-Mechanical Stresses in Flip-Chip Packaging” MATEC Web of Conferences, 95, 01003 DOI: 10.1051/matecconf/20179501003

  • Omid Nabinejad, Sujan Debnath and Mohammad Mohsen Taheri (2017) “Oil Palm Fiber Vinylester Composite; Effect of bleaching treatment” Materials Science Forum, 882, pp. 43-50 

  • Sujan Debnath (2017) “Editorial Preface” Materials science forum. , 2017, Vol.882; Identifier: ISSN: 0255-5476 , 1662-9752; ISBN: 9783038357322.

  • Pang, J. N. I., H. G. Harno, and V. C. C. Lee. 2017. “On-off skyhook semi-active control via a magneto-rheological (MR) damper for airfoil-based energy harvesting systems.” In International Conference on Materials Technology and Energy, Apr 20, 2017, Miri, Sarawak, Malaysia

  • Lee, V. C. C., and J. C. Chong. 2017. “Effects of intermediary reservoir in a two-stage impedance pump.” In The 9th International Unimas Stem Engineering Conference (ENCON 2016) “Innovative Solutions for Engineering and Technology Challenges”, Oct 26, 2016, Kuching, Sarawak, Malaysia

 

List of Publications:2016

  • Law, M. C., E. L. Liew, S. L. Chang, Y. S. Chan, and C. P. Leo. 2016. “Modelling microwave heating of discrete samples of oil palm kernels.” Applied Thermal Engineering 98: 702-726.

  • Ting Chiong Yue, Haidar F. AL-Qrimli, Hydrodynamic Analysis of Submersible Robot, International Journal of Advanced Research and Development, Volume 1; Issue 9; September 2016; Page No. 20-24. http://www.advancedjournal.com/archives/2016/vol1/issue9

  • Karam S. Khalid, and Haidar Fadhil Al-Qrimli, Examine bi-metallic rectangular thin walled tube under different trigger mechanisms, Advanced Materials Science, Vol 1(1): 4-8; (2016),   doi: 10.15761/AMS.1000102.

  • Haidar F. Al-Qrimli, Karam S. Khalid & Ahmed M. Abdelrhman, Roaad K. Mohammed, Husam M. Hadi, A Review on a Straight Bevel Gear Made From Composite, Journal of Materials Science Research, Vol. 5, No. 3; (2016). doi:10.5539/jmsr.v5n3p73.

  • Rahmat Izaizi, Firas B. I., Haidar F. AL-Qrimli, Artificial Intelligence Application in Power Generation Industry: Initial considerations. IOP Conf. Series: Earth and Environmental Science 32 (2016) 012007. DOI: http://dx.doi.org/10.1088/1755-1315/32/1/012007.

  • Jung, H.C. and Krumdieck, S., Meanline design of a 250 kW radial inflow turbine stage using R245fa working fluid and waste heat from a refinery process, Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, (2016). (ISI, IF 0.645)

  • Omid Nabinejad, Sujan, M. E. Rahman, Willey Y. H. Liew, Ian J. Davies (2016) “Mechanical and Thermal Characterization of Polyester Composite Containing Treated Wood Flour from Palm Oil Biomass” Polymer Composites, Wiley (in Press) (ISI & SCOPUS indexed, IF 2.324)

  • Sujan, M. M. Reddy and S. Y. Qua (2016) “Influence of cutting fluid conditions and cutting parameters on surface roughness and tool wear in turning process using Taguchi method” Measurement, Elsevier, Vol. 78, pp 111-119 (ISI & SCOPUS indexed, IF 2.359)

  • Haidar F. AL-Qrimli, Ahmed M. Abdelrhman, Husam M. Hadi, Roaad K. Mohammed, Hakim S. Sulta, Three Dimensional Spur Gear Static Contact Investigation Using Finite Element Method. Canadian Journal of Modern Applied Science; ISSN 1913-1844; Vol. 10, No. 5; (2016).

  • Aja Ogboo Chikere, Hussain H. Al-Kayiem, Mesfin Gizaw Zewge and Meheron Selowara Joo “Overview of Hazardous Waste Management Status in Malaysia” in Management of Hazardous Wastes, InTech Open Science, 2016, ISBN: 978-953-51-4764-0. Index in the Book Citation Index in Web of Science™ Core Collection (BKCI) and BIOSIS Previews (Thomson Reuters).

  • Wee, S. K., Y. W. Pok, M. C. Law, and V. C. C. Lee. 2016. “The study of solid circulation rate in a compartmented fluidized bed gasifier (CFBG).” In International Conference on Chemical Engineering and Bioprocess Engineering, Dec 9, 2015, Kota Kinabalu, Malaysia

  • Law, M. C., and E. L. W. teng. 2016. “Simulation of a Bioreactor with an Improved Fermentation Kinetics – Fluid Flow Model.” Pertanika Journal of Science & Technology 24 (1): 137-163.

  • Aja Ogboo Chikere, Hussain H. Al-Kayiem and Zainal Ambri Abdul Karim (2016) “Thermal Diffusion Performance of a Diffuser by various Guide Vanes configurations” in the proceeding of the UTP-UMP Symposium on Energy Systems (SES 2016)

 

List of Publications:2015

  • Lee, V. C. C., Y. A. Abakr, and K. C. Woo. 2015. “Dynamics of fluid in oscillatory flow: The Z component.” Journal of Engineering Science and Technology 10 (10): 1361-1371.

  • Lee, V. C. C., H. V. Lee, H. G. Harno, and K. C. Woo. 2015. “Comparative performance analysis of a dual-solenoid mechanical oscillator.” In 9th Curtin University of Technology Science and Engineering International Conference 2014 (CUTSE2014), Sarawak

  • Law, M. C., G. V. Y. Liang, V. C. C. Lee, and S. K. Wee. 2015. “Temperature and voltage responses of a molten carbonate fuel cell in the presence of a hydrogen fuel leakage.” In 9th Curtin University of Technology Science and Engineering International Conference 2014, Dec 3, 2014, Sarawak, Malaysia: IOP Publishing.

  • Law, M. C., V. C. C. Lee, and C. L. Tay. 2015. “Dynamic behaviors of a molten carbonate fuel cell under a sudden shut-down scenario: The effects on temperature gradients.” Applied Thermal Engineering 82: 98-109.

  • Lee, V. C. C., M. C. Law, and S. K. Wee. 2015. “Theory to practice on finite element method and computational fluid dynamics tools.” Australasian Journal of Engineering Education 20 (2): 123-133.

  • Haidar F. AL-Qrimli, A. A. Oshkour, Firas B., Fadhil Abbas Mahdi, Material Design Consideration for Gear Component Using Functional Graded Materials. International Journal of Materials Engineering Innovation. Vol. 6, No. 4, (2015).

  • O. Nabinejad, D. Sujan, M. E. Rahman, and Ian J. Davies “Determination of filler-content for natural filler polymer matrix composite by thermogravimetric analysis” Journal of Thermal Analysis and Calorimetry, Springer

  • O. Nabinejad, D. Sujan, M. E. Rahman, and Ian J. Davies “Effect of oil palm shell powder on the mechanical performance and thermal stability of polyester composites” Materials and Design.

  • M. M. Reddy, A. Gorin, K.A. Abou-El-Hossein, D. Sujan “Modeling of Temperature Distribution when Machining Inconel 718 in Turning process” Power Electronics and Energy Engineering.

  • Haidar Fadhil Al-Qrimli, Haider A. Almurib, Nandha Kumar, Carbon/epoxy woven composite experimental and numerical simulation to predict mechanical performance, Journal of Advances in Materials Science and Applications AMSA, Vol.4,pp.33-41, (2015).

  • P. R. K. Fu, Z. Oo, D. Sujan “Microstructure analysis, physical and thermal properties of Al2O3-Al2TiO5 functionally graded ceramics for the application of car brake rotor” JST Vol. 23 (1).

  • Haidar F. Al-Qrimli, Haider A. Almurib, Nandha Kumar, F. A. Mahdi, Dynamic Analysis of a Straight Bevel Gear Composite Structure, Journal of Material Sciences & Engineering, ISSN: 2169-0022 JME. Vol.4:1, (2015).

  • Haidar F. AL-Qrimli, Karam. S. Khalid, Fadhil A. Mahdi, The effect of cone angle on composite tubes subjected to axial loading, British Journal of Applied Science & Technology, Science Domain International. 7(4), BJAST.2015.152, ISSN: 2231-0843, (2015).

  • Reddy, M.M., Sujan D. and Lee L.C. (2015) “Modeling of Temperature Distribution when Machining Inconel 718 in Turning process”, Power Electronics and Energy Engineering, pp 207-210.

 

List of Publications:2014

  • D. Sujan, M. M. Reddy and S. Y. Qua (2014) “Environmental friendly cutting fluids and cooling techniques in machining: A review” Journal of Cleaner Production, Elsevier, Vol. 83 pp 33-47

  • O. Nabinejad, D. Sujan, M. E. Rahman, M.M. Reddy, Willey Y. H. Liew and Ian J. Davies (2014) “The effect of alkali treatment of OPKS filler on mechanical property of polyester-composite” Advanced Materials Research Vol. 980 pp 86-90

  • Ng Samuel, D. Sujan, M. E. Rahman, O. Nabinejad and M. M.  M. Reddy (2014) “Oil Palm Fibre and Nano-Silica Reinforce d Epoxy Composite Material” Advanced Materials Research Vol. 980 pp 23-27

  • Y. R. Loh, D. Sujan, M. E. Rahman, C. A. Das (2013) “Sugarcane bagasse-The future composite material: A literature review” Resources Conservation and Recycling, Elsevier, Vol 75, pp 14– 22

  • M. E. Rahman, A. S. Muntohar, V. Prakash, B. H. Nagaratnam, D. Sujan (2014)  “Self compacting concrete from uncontrolled burning of rice husk & blended fine aggregate”, Materials and Design. Elsevier, Vol 55, pp 410-415

  • D. E Woldemichael, J. J. Lai, D. Sujan (2014) “Topology optimization of beam structures with various end loading conditions”, Applied Mechanics and Materials, Vol. 465-466, pp 22-26

  • D. Sujan, C. W. Nguong, S. N. B. Lee, M. Gizaw (2014) “Wear properties of oil palm cellulose fibre reinforced polymer composites”, Advanced Materials Research, Trans Tech Publications Ltd, Vol. 845, pp 81-85

  • D. Sujan, T. K. Piaw, D. E Woldemichael (2014) “Thermo-mechanical stress analysis in electronic packaging with continuous and partial bond layer”, Applied Mechanics and Materials, Vol. 465-466, pp 50-54

  • D. Sujan, X. B. Pang, M. E. Rahman, M. M. Reddy (2014) “Performance of solder bond on thermal mismatch stresses in electronic packaging assembly” Materials Science Forum, Vol. 773-74, pp 242-249

  • M. M. Reddy, A. Gorin, K.A. Abou-El-Hossein, D. Sujan (2014) “Machinability of aluminum nitride ceramic using TiAlN and TiN coated carbide tool insert” Materials Science Forum, Vol. 773-774, pp 437-44.

  • Lee V C C, Gan H S, Abakr Y A and Woo K C, 2014. Bulk Flow Behaviour of a Two-Stage Impedance Pump. Engineering Letters. 22(2), pp 53-62. ISSN 1816-0948.

  • Reddy, M.M., Alexander, G., Abou El, H.K.A. and Sujan, D. (2014) “Machinability of Aluminum Nitride Ceramic using TiAlN and TiN Coated Carbide Tool Insert”, Materials Science Forum, 773-774: 445-455.

 

List of Publications:2013

  • M. G. Zewge, T. A. Lemma, A. A. Ibrahim, D. Sujan, “Modeling and Simulation of a Heat Recovery Steam Generator Using Partially Known Design Point Data”, Advanced Materials Research, Vol 845, pp. 596-603, Dec. 2013

  • Y. R. Loh, D. Sujan, M. E. Rahman, C. A. Das (2013) “Sugarcane bagasse-The future composite material: A literature review” Resources Conservation and Recycling, Elsevier, Vol 75, pp 14– 22

  • C. W. Nguong, S. N. B. Lee, D. Sujan (2013) “A review on natural fibre reinforced polymer composites” World Academy of Science, Engineering and Technology, Vol 73, pp 1123-1130

  • M. M. Reddy, A. Gorin, K.A. Abou-El-Hossein, D. Sujan (2013) “Surface roughness model when machining aluminum nitride ceramic with two flute square end micro grain solid carbide end Mill” Advanced Materials Research, Trans Tech Publications Ltd, Vol. 747, pp 282-286

  • L. J. Fei, D. Sujan (2013) “Origami theory and its applications: A literature review” World Academy of Science, Engineering and Technology, Vol 73, pp 1131-1135

  • D. Sujan, K. P. Ting (2013) “Closed form bi-layered interfacial thermal stress model in electronic packaging” International journal of Advanced Materials Manufacturing and Characterization (IJAMMC)

  • L. Lancaster, M. H. Lung, D. Sujan (2013) “Utilization of agro-industrial waste in metal matrix composites: towards sustainability” World Academy of Science, Engineering and Technology, Vol 73, pp 1136-1144.

  • Lee V C C, Abakr Y A and Woo K C, 2013. Valveless Pumping Using A Two-Stage Impedance Pump. Frontiers in Mechanical Engineering. 8(3), pp 311-318. ISSN 2095-0241.

 

Share this